BGP and Route-Domains

Hey Steve!

Yes, I did add

/0

ltm virtual vs_rd1 {
    destination 0.0.0.0%1:any
    mask any
    profiles {
        fastL4 { }
    }
    source 0.0.0.0%1/0
    source-address-translation {
        pool cgnat_pool
        type lsn
    }
    translate-port disabled
    vlans {
        VLAN_701
    }
    vlans-enabled
}

ip r

[admin@f5CGNAT:/S1-green-P:Eval:Active:Standalone] ~  ip r
192.168.148.116/30 dev VLAN_709  proto kernel  scope link  src 192.168.148.117 
127.1.1.0/24 dev tmm0  proto kernel  scope link  src 127.1.1.1 
127.3.0.0/24 dev mgmt_bp  proto kernel  scope link  src 127.3.0.1 
198.82.245.0/24 dev mgmt  proto kernel  scope link  src 198.82.245.112 
198.82.245.0/24 dev mgmt  scope link  src 198.82.245.112  metric 9 
127.2.0.0/24 dev mgmt.1  proto kernel  scope link  src 127.2.0.2 
127.7.0.0/16 via 127.1.1.254 dev tmm0 
127.20.0.0/16 dev tmm_bp  proto kernel  scope link  src 127.20.1.254 
default via 198.82.245.1 dev mgmt  metric 9  mtu 1500

[admin@f5CGNAT:/S1-green-P:Eval:Active:Standalone] ~  rdexec 1 ip r
172.14.0.4/30 dev VLAN_701  proto kernel  scope link  src 172.14.0.5 
127.1.1.0/24 dev tmm0  proto kernel  scope link  src 127.1.1.1 

Turned on logging. Pretty much seeing keepalives for neighbor relationships. I'm using "neighbor x.x.x.x default-originate" instead of "network 0.0.0.0/0", and I can now see the default getting advertised by BGP.

f5CGNAT[1]show ip bgp neighbors 172.14.0.4 advertised-routes 
BGP table version is 6, local router ID is 1.1.1.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete

   Network          Next Hop            Metric     LocPrf     Weight Path
*> 0.0.0.0/0        172.14.0.5                        100      32768 i
*> 172.24.0.0       172.14.0.5                                 32768 ?

But my question again, the default above is not a virtual server route that references an LSN pool. It was introduced because of "default-originate". How do clients get NAT'd if the are not connecting to the virtual server? "show ip route" shows the default virtual server route. How can I advertise that using BGP.

f5CGNAT[1]show ip route 
Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
       O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

K*      0.0.0.0/0 is directly connected, tmm0
C       127.0.0.1/32 is directly connected, lo
C       127.1.1.0/24 is directly connected, tmm0
K       172.24.0.0/16 is directly connected, tmm0
C       172.14.0.4/30 is directly connected, VLAN_701

Thanks.